Esprit120 – Page 2 – IMT3b Observatory

Viewing Report 23rd/24th August 2019 – IMT3 Observatory

Viewing time period – 22:34 – 0

Looking at Vega ready for setting up guide scope

GingerGeek round tonight to align his guide scope, focus it and make sure guiding works. The first thing we had to do though was unplug my camera and then plug his into the Mount Hub Pro due the fuse problem from the last session when it melted through the fuse holder, that will be fixed later this weekend.

Next we slewed to Vega as seen above and took a quick image to see how far out the Esprit 120 is compared to where the OS12″ is pointing so that we can adjust it later.

So it would seem focusing was a bit more of a challenge than we thought. The first thing is we bought an adapter for the guide scope (aka the finder that came with the Esprit 120) but it did not provide enough back focus for the camera. We had a look round the adapters in the dome and found a nose extension for the Lodestar, however it was not a c-mount end to it so we landed up duck taping it on tonight until GingerGeek can bring round his adapter.

The next challenge was not seeing any stars in the lodestar, after what seemed like a long while we came to the conclusion that the picture we were looking at on the screen in PHD2 was not the camera we thought, it was instead the one from the OS12″ which at this point was not pointing through the slit.

After looking through the settings on PHD2 we found a new setting we had not seen before, which seemed to be because we have multiple ASCOM cameras connected.

The symbol is a double arrow and when clicked a drop down list of 4 Starlight Xpress cameras appeared, so we chose the 4th one which was one of the two Lodestars and that worked.

I then adjusted the guide scope in its two ring holders and aligned close to Vega which we had slewed to. Now the guide scope was spot on and the main scope ever so slightly off. This will be solved when we either shim the scope to align with the OS12″ or when we add/change the way in which it is connected to the losmandy mounting plate.

By 12:40am we had the focus sorted for the guide scope and we moved back in doors to connect back to the 2 cameras for this evening, lodestar and main imaging camera and then the Lakeside focuser to start an autofocus run on the main camera.

At 1:20am we were still trying to focus as we had not setup the autofocus routing for the Esprit 120 before, the OS12″ is now fine but this was a new challenge. GingerGeek spend an appreciable amount of time changing the step size and other settings in SGPro to effect the focus routine. Finally autofocus did a great job and we landed up at a focus point of 6225 for the Luminance filter. However there was an amount of backlash and this caused the focus point to not be the same in a one direction. GingerGeek needs to find out where he wrote down the figure we measured for backlash so we can add in.

Good auto focus achieved but with slight error

Next we slewed to the star near the Elephant Trunk, SAO 33570 and changed the filter to Ha. GingerGeek then started an auto focus run for this filter. As it was now late we were missing setting simple things such as the exposure time increase from 1s to 15s needed to actually register any stars to focus on.

Once focused (ish) as we are tired now, we started a short test image run of 10mins subs for the Ha. GingerGeek showed me the Big Status window which is a much nicer interface to your image progress.

We then had a problem with guiding, there were inconsistent rates between the RA and DEC axis. This caused trailing of stars so we stopped the guiding, however the next image although still out of focus showed promise especially given we were not guiding.

10min unguided Ha Esprit 120 (out of focus)

So 3:24am and time for bed.

Viewing Report 20th/21st July 2019 – IMT3 Observatory & Travel Scope

Viewing time period – 21:15 – 02:15

There were two things I wanted to do tonight, one was to get first light with GingerGeek through the Skywatcher Esprit 120ED, the other was to setup my Esprit 120 on the MyT in the garden and grab a photo of the Moon to celebrate 50 years since Neil and Buzz stepped out onto the lunar surface. As a bonus I wanted to to get the guiding working on the MyT too.

As GingerGeek opened the dome on the IMT3 I setup the portable gear on the patio. I connected the setup to a 12V car battery to see how well it did at running the Mount and the camera. The initial voltage of the battery was 13.1v when I started. I connected the camera to EZCap and the Mount to TheSkyX (TSX).

Meanwhile GingerGeek opened the dome, connected the mount, opened the very geeky but cool Flip Flap covering the Esprit 120 and slewed to a bright star for deterring the focus and the position relative to the 12″ main scope.

Remarkably the focus was fairly near and after a few iterations GingerGeek managed to get the V curve sorted for good focus. Before this was done he setup the Luminance filter on the filter wheel control with SGPro that had not been configured. I then looked at the resulting image and determined the FoV within TSX. The field almost fits the 12″ and so the position is fairly close, close enough for solving and being in the right area for imaging. There was an error by SGPro complaining about 800px difference with what was to be expected, the problem being the difference in the angle of the Esprit 120 vs where the mount knows it is pointing as shown through the 12″.

Despite that we managed to take an image and then move on to see if we could guide with the 12″ off-axis guider for the Esprit. This worked a little but the guider graph was way off at various points, I believe this is potentially either a setup issue on the guider and/or the fact that we are too frequently taking too many images to correct and thus chasing the seeing. I will look at this next time are out.

Back on the portable setup, I managed to very quickly connect, perform polar alignment using the PoleMaster and the new bracket I fitted. I then slewed to a star which was not quite in the FoV so I need to spend more time on this next time I am out. No problems though, I nudged the scope and found the star. Performing a sync on this solved any further slewing problems.

I then waited for the Moon to come up over the roof tops which was unfortunately not until 2am of the 21^st thus slightly missing the landing date of 20th by 2 hours (Eagle landed at 9:17pm BST) but non the less still obtaining an image of the Moon to celebrate the 50^th anniversary of the first lunar landing at the time Neil put that famous foot on the Moon at 1:56am BST on the 21^st July 1969 🙂

GingerGeek managed to get a few images but nothing much was showing on them especially the Elephant Trunk nebula he was imaging, I suspect, but am not sure, the wrong filter was selected so probably OIII rather than Ha as a previous Frame and Focus command through SGPro for 15 seconds showed the Elephant Trunk, at this point we were taking 10 minute exposures so it should have easily been visible. Again another problem to sort next time we are out.

Viewing Report 29th/30th June 2019 – IMT3 Observatory & Travel Scope

Viewing time period – 22:01 – 03:18

Tonight Bob will be learning how to control the observatory and using the Tak FS102 to trying imaging. Meanwhile I will be setting up my new Paramount MyT on its Berlebach tripod and with a new Sky-Watcher Esprit 120 mounted on top. The business end has my new QHY168C, yes I purchased a 2nd one, they are that good.

Whilst Bob played, I setup the travel kit on the new patio. I realised I could connect the camera through the USB on the MyT to one cable that won’t get snagged. I will however need to connect a power for the camera as that is currently trailing. There is a power connector on the back of the mount but I believe it is only rated to 1amp. There is however another power out which is rated at 7.5 amps so I will buy a Tycoon KPPX-4P 4 pin couple of connectors and makeup a cable so I can plug into that directly.

So I connected to TheSkyX with the mount and slewed to Arcturus. I could not connect the QHY camera to TheSkyX as I seem to be missing a driver. I will take a further look tomorrow to see if there is one. Instead I used the EzCap software they provide and connected the camera to that.

I focused manually as I have not motor focus to keep things simple, and soon had stars in view. I then did a manual spiral search until I found Arcturus and then synced on it. I could then slew around the sky with ease.

For polar alignment I have ordered (my friend GingerGeek has ordered) a PoleMaster mounting plate that I can use, this will make it easy to align. Tonight I just plonked the mount down without any polar alignment, thus anything more than 10 seconds produced trailing.

I tested cooling the camera, slewing and parking, although I need to see the park position 180 degrees from the current position to allow the scope rings to be in the right place for removing the OTA.

The scope and the mount and the camera make a great travel setup, each component is not too heavy to move by itself, the connection and setup is fairly straightforwards and I really do look forward to testing this out in October in Tenerife. I do need to test running from a car battery to see how long things last. I have my car battery I use for astronomy on charge and will test next time.

The connection of the camera to the flattener is a push fit and is missing the luminance filter. I will order the right adapters from Modern Astronomy so that I can fit later.

So I still have a few things to make, buy, test and do before October but good progress tonight on the travel setup front.

Meanwhile Bob has been making good progress with the Tak FS 102 in the IMT3. Imaging Arcturus and testing lengths of exposure on different objects such as M13. Some pieces of the sky Bob was imaging at 5 minutes unguided and others such as M13 only 3 minutes. I need to look at why this is given I now think the polar alignment from last night is excellent.

I reset the FoV indicator for the Tak FS102 in relation to the main 12″ scope. I need to find a way of slewing to given object for the offset scopes. I also need to be shown how you use SGPro to slew too, rather than using TheSkyX, so a slew, plate solve and then final adjustment.

Viewing Report 22nd/23rd June 2019 – IMT3 Observatory

Viewing time period – 22:00 – 02:31

Tonight Bob and GingerGeek came over to progress with commissioning the observatory. The task for tonight was to get the Esprit 120 focused and given first light. As the evening progressed there was slight frustration of how long it was taking to sync on a star, in terms of finding it and then being able to sync so we could go back to it. This is because I had been the night before messing with the polar alignment and we have yet to perform a Point run.

It also took some time to get focused on the Esprit due to us setting the maximum extent to the focuser tube incorrectly, falling short of the distance needed at the back focus to get good focus. We then had to go into the observatory and modify the maximum out figure for the Lakeside focuser.

Once this was done focus was achieved and GingerGeek used autofocus within SGPro to get good focus.

A single image was taken to prove it.

Next we need to refine the polar alignment with a TPoint run and then perform a longer Point run to finish the commissioning of the Paramount MEII.